Login | Register
产品中心
Home > Product > Flow instrument > AOLG-I/C series standard nozzle throttling device

AOLG-I/C series standard nozzle throttling device

    AOLG-I/C series standard nozzle throttling device

  • Category:
    Flow instrument
  • Browse number:
    876
  • Release time:
    2025-05-06 16:48:28
  • Share:
  • INQUIRY

scope of application


Standard nozzles have the characteristics of high temperature and high pressure, impact resistance, long service life, large measurement range, and high measurement accuracy. Suitable for measuring high-temperature and high-pressure steam flow in power plants, heating network pipelines, high flow rates, and fluid and flow rates. There are two specific types:


ISA1932 nozzle (standard nozzle) and long diameter nozzle.


● Main technical specifications


▲ Main technical characteristics


Corner pressure standard nozzle: suitable for DN50-1000mm, PN1.0-32MPa, Reynolds number Red range of 2 × 104-2 × 106, diameter ratio β (within the range of 0.32 to 0.80). Recommended Reynolds number Red min for corner joint pressure standard nozzle


β Red min β Red min β Red min


0.320 4.05×104 0.500 4.94×104 0.675 4.66×104


0.350 3.93×104 0.525 5.22×104 0.700 3.42×104


0.375 3.95×104 0.550 5.49×104 0.725 2.00×104


0.400 4.04×104 0.575 5.69×104 0.750 2.00×105


0.425 4.19×104 0.600 5.78×104 0.775 2.97×105


0.450 4.40×104 0.625 5.69×104 0.800 5.19×105


0.475 4.66×104 0.650 5.35×104


When the pressure standard nozzle with corner joint is used above the Reynolds number listed in the table above, the change in flow coefficient caused by flow rate variation shall not exceed 0.5% compared to the actual value.


Specifications and Structure


ISA1932 nozzle


● Long diameter nozzle


The combined distance pressure measuring long diameter nozzle flow device is a differential pressure generating device for measuring flow. With various differential pressure transmitters, it can measure various fluid flow rates in circular pipes, especially suitable for measuring high-temperature and high-pressure liquids filled in circular pipes.


▲ Performance and Application


·This device is suitable for measuring high-temperature and high-pressure liquids filled with circular tubes (especially used in the main steam pipeline of 6-360MW steam turbine generator units).


·Usage conditions: Inner diameter of pipeline: 50mm ≤ D ≤ 630mm, diameter ratio: 0.20 ≤ β ≤ 0.80


Reynolds number: 104 ≤ Red ≤ 107 Relative roughness: K/D ≤ 10 × 10-4


·This device cannot operate in reverse


·Recommended Reynolds number


β αβ2


Redmin


(×104)


β αβ2


Redmin


(×104)


β αβ2


Redmin


(×104)


0.20 0.0387 5.25 0.45 0.1970 11.8 0.70 0.5294 18.4


0.25 0.0604 6.45 0.50 0.2454 13.2 0.75 0.6395 19.7


0.30 0.0868 7.87 0.55 0.3009 14.5 0.80 0.7814 21.0


0.35 0.1182 9.18 0.60 0.3650 15.8


0.40 0.1548 10.5 0.65 0.4400 17.1


Specifications and Structure


▲ Main product varieties and specifications


Model Steam quantity t/h Usage pressure, temperature Pipe diameter Generator set MW


AOLCP—39—1 35 φ159×7 6


AOLCP—39—2 65 φ219×9 12


AOLCP—39—3 130


3.9Mpa,450°C


φ273×11 25


AOLCP—100—1 130 φ219×16 25


AOLCP—100—2 220、410


10Mpa, 540 ° C, diameter 273 × 20, 50, 100


AOLCP—140—1 400 14Mpa,555°C φ273×30 125


AOLCP—140—2 670 14Mpa,540°C φ377×36 200


AOLCP—170—1 1000 17Mpa,555°C φ377×56 300


·This device includes a measuring tube, nozzle, pressure tapping tube, support switch, pin, and nameplate.


·The total length of the measuring tube is 6D (front 4D, back 2D).


·The material for measuring the pressure connection of the measuring tube is 12Cr1Mov, and the material for the nozzle support ring is 1G18Ni9Ti. Special material ordering will be discussed in person.


·It is recommended to use high ratio long diameter pipes (our factory has always used high ratio). If using low ratio long diameter nozzles, it is recommended that β be greater than 0.32 because β is too small and the loss is too large (the transmitter range can be changed). If a low ratio long diameter nozzle with β less than 0.3125 must be used, the downstream pressure hole cannot exceed the nozzle outlet edge.


标准喷嘴节流装置


Long diameter nozzle:


    


ONLINE MESSAGE

*Subject:
*E-mail:
Phone:
Company:
*Captcha:

RELATED PRODUCTS

Contact Us

Company Address:

Building 5 and 11, Fuzhou IoT Industrial Park, 

No. 12 Xingye West Road, Mawei District, 

Fuzhou City, Fujian Province, China

Market Cooperation:

Manager Guo: +8613959146212


Copyright © 2025 Fujian Aotai Automation Equipment Co., Ltd

This website uses cookies to ensure you get the best experience on our website.

Accept Reject